CSWIP 3.1 Multiple Choice Paper 8

Answers don’t show in the following questions; we separated to another link. You should spend your time and focus to read, answer the questions correctly, then it is the time to review your results.

Note 1. Don’t remember the questions and answers.
Note 2. Should be used exclusion principle to choose the best answer.

Rolling down the end page to get the answer link :arrow_double_down:

  1. Which of the following defects do you not expect to find by visual examination of completed welds?
  • Linear slag inclusions
  • Under cuts
  • Overlap
  • Linear misalignment
  1. Stress relief is not helpful in one of the following cases. Which one?
  • In improving resistance to stress corrosion cracking
  • In dimensional stability after machining improving
  • In lowering the peak residual stress
  • In softening the steel
  1. Welding a steel plate of CE of 0.45 would require preheating to?
  • Prevent the formation of sulphides
  • Prevent hardening in the HAZ
  • Prevent the formation of carbides
  • To improve mechanical properties in the weld
  1. What effect to low ductile steel plate normally has when they are located outside weld zone?
  • Cause lamellar tearing
  • Fuse together to form a bond
  • Affect the weld metal composition
  • Cause internal tearing on a micro-scale
  1. Which of the following processes uses the “keyholing” system of fusion?
  • Friction welding
  • Diffusion bonding
  • Electron beam welding
  • Autogenous TIG welding
  1. When hydrogen control is specified for a manual metal arc-welding project the electrode would normally be:
  • Cellulosic
  • Iron oxide
  • Acid
  • Basic
  1. You would with certainty recognize a hydrogen controlled flux covered electrode from it’s:
  • Color
  • Length
  • Trade name
  • AWS/EN Code Letter
  1. When 111 process is being carried out on an country pipeline, which groups of welder are most likely to require continuous monitoring?
  • Concrete shuttering welding team
  • Pipe welders
  • Platter welders
  • Plant maintenance welders
  1. You noticed manual metal arc welding electrodes, stripe of flux, are being used as filler wire, for TIG welding. You would object because:
  • It is too expensive
  • The wire would be too thick
  • The weld metal composition may be wrong
  • The wire is too short
  1. When open site working, serious porosity in manual metal arc welding is brought to your attention. What would you investigate?
  • Electrode type
  • Power plant type
  • Electrode storage
  • Day temperature
  1. The steel composition in structural contract is changed form 0.15% carbon, 0.6% manganese, to 0.2% carbon, 1.2% manganese. Might this influence the incidence of:
  • Porosity
  • Cracking in the weld area
  • Under cut for fillet welds
  • Lack of root fusion defects
  1. One of the following alloys is non-magnetic, Which?
  • 4.0% Cr Mo
  • 12.0% Cr
  • 18% Cr ,8% Ni
  • 9.0% Ni
  1. When the TIG welding austenitic stainless steel pipe. Argon gas backing is called for.
  • Prevent oxidation
  • Prevent under bead cracking
  • Prevent porosity
  • Control the penetration bead shape
  1. Pre-heating a carbon steel manual metal arc welding is carried out to minimize the risk of
  • Scattered porosity
  • Worm hole porosity
  • Parent metal cracking
  • Lack of penetration
  1. In ISO 2553 specifies that the drawing dimension quoted for a fillet weld is the:
  • Leg length, z
  • Actual throat thickness
  • Deposit thickness
  • Design throat thickness
  1. For open site manual metal arc welding the following equipment is available. Which would you choose for safe working?
  • Single operator transformer
  • Multi operator transformers
  • AC/DC composite power unit
  • Diesel engine driven motor generator
  1. If submerged welding to be used to make butt welds, which would you be most critical of:
  • The root gap tolerance
  • The angle of penetration
  • The root face width
  • The gas cut finish
  1. During CO-2 welding, the arc length is most likely to be affected by:
  • The wire diameter
  • The current return connections
  • The gas flow rate
  • The torch to work angle
  1. Pre heating for arc welding applies to:
  • Assembly welding only
  • Assembly and tack welding
  • Joint over 25 mm thick only
  • Cruciform welds only
  1. You see a welder using oxy-acetylene flame with along feathered inner cone. What would be the effect of this on carbon steel?
  • The weld could be hard and brittle
  • The weld metal could be too soft
  • There will be no effect on the weld
  • The weld have under cut
  1. A welder qualification test is o verify:
  • The skill of the welder
  • The quality of the materials
  • The non-destructive procedures
  • The manufacturing methods
  1. A fabricating procedure calls for fillet welds to be blended in by grinding. This is to influence:
  • HAZ cracking
  • Fatigue life
  • Residual stresses
  • Yield strength
  1. Bend test specimens have been taken from a 25 mm thick carbon steel butt weld. Which would show lack of inter-run fusion:
  • Side bend
  • Root bend
  • Face bend
  • Guided bend
  1. Lamellar tearing has been occurred in steel fabrication. BEFORE welding could it have been found by:
  • X-ray examination
  • Dye penetrant
  • Ultrasonic inspection
  • It would not have been found by any inspection method
  1. You are to over see arc welding of some machine fittings and find they are cadmium plated. What you:
  • Permit it to proceed
  • Permit it to proceed with fume extraction
  • Stop the operation at once
  • Advise the welder to drink milk and proceed
  1. What two functions in arc welding must be in equilibrium to enable a stable arc to be established?
  • Arc voltage
  • Current
  • Wire/electrode feed rate
  • Metal burn-off rate
  1. In MMA welding, what parameter is used for the control penetration into the base material?
  • Voltage
  • Welding speed
  • Iron powders in the coating
  • Current
  1. In the welding of butt joint from one side, which of the following controls the profile of the root bead?
  • Root Face
  • Bevel Angle
  • Root Gap
  • One of the above
  1. What type of power source characteristic is required for manual welding?
  • Constant voltage
  • Flat Characteristic
  • Drooping Characteristic
  • Motor Generator
  1. Which of the following destructive tests would indicate the toughness of weld metal/parent metal - HAZ.
  • Macro
  • Nick break
  • Hardness
  • CVN

See suggestion answer here.

NOTE : You have to signed-up to become a member prior to view the answers here.

1 Like

This spec replaced by ISO 2553

Please check again question No 4,17,18,

Please get answer here.

1 Like
When hydrogen control is specified for a manual metal arc-welding project the electrode would normally be:

Cellulosic
Iron oxide
Acid
Basic-low hydrogen <5ml/100gram
1 Like

Current -control the penetration in MMA

2 Likes

We have updated the answers at the end of each topic. You may check it and correct me if I am wrong.
Thanks!